Monday, November 17, 2008
Posting # 8 Topping off The Beast
Friday, November 7, 2008
Posting #7 The Beast is not a beauty --- yet
I am only spending an hour here and there so not much change in the Beast. I decided against constructing a double hull on the sides and I have re-designed the trunk. The trunk allows the dagger board to be forced down through bottom of the boat making it possible to sail. These changes should keep the boat light (under 120#).
I finished addi
Tuesday, October 28, 2008
Posting # 6 The Belly of the Beast
As you may have concluded I have decided on “Le Bete de la Mer” French for “The Beast of the Sea” as the name for my boat. I usually call it “The Beast”. I am working on the interior hull (the belly of the beast).
In the picture you can see Carmel, our dog, is sitting in the The Beast. I am using Styrofoam board between the exterior and interior hull. The Styrofoam will give it more floatation in case a tsaumi swamps The Beast. Behind Carmel is what is referred to as the “trunk” for the dagger board and mast.
Friday, October 17, 2008
Posting # 5 Stitch-and-Glue
Stitch-and-glue construction is a technique using plywood, wire, glue, fiberglass cloth, epoxy fillers, and epoxy resin.
I stitched the bottom to the sides with wire along the seams. The wire holds the panels together until the glue is cured (I am using PL premium construction adhesive). I will remove the wires in a few days.
One nice thing about stitch-and-glue construction is that fewer tools are required compared to other methods of construction
Sunday, October 12, 2008
Posting # 4 “Le Bete Del La Mer” is beginning to look like a Boat
Thursday, October 9, 2008
Posting # 3 – Feedback
Thanks to all that have given me feedback on my boat-building project. Comments range from support to concern interspersed with skepticism. Mom and Dad are happy that I know how to swim and but have advised me to purchase life preservers. Gregory has advised me to be patient and to use a lot of clamps. Tim has suggested that I name my boat “In Denial”.
About the name, some are thinking I already named my boat “Summer Breeze”, not true. I am using plans for a boat called “Summer Breeze”. Full plans are available on the Internet. The plans for this boat won a challenge sponsored by the website Ducksworks http://www.duckworksmagazine.com. I will be
making changes to the plans as I go. Hopefully these changes will be improvements. I have not pick a name for the boat and welcome any suggestions. I am considering Tim’s suggestion “In Denial”. I might name it after a work of art by Matisse “Les Betes De La Mer ”The Beast of the Sea”.
About the name, some are thinking I already named my boat “Summer Breeze”, not true. I am using plans for a boat called “Summer Breeze”. Full plans are available on the Internet. The plans for this boat won a challenge sponsored by the website Ducksworks http://www.duckworksmagazine.com. I will be
making changes to the plans as I go. Hopefully these changes will be improvements. I have not pick a name for the boat and welcome any suggestions. I am considering Tim’s suggestion “In Denial”. I might name it after a work of art by Matisse “Les Betes De La Mer ”The Beast of the Sea”.
Monday, October 6, 2008
Posting # 2 Creating a Workspace, Tools and Materials - click on images to enlarge
I have spent the last two weeks reading and rereading the two sets of plans I am using to build my boat (the Summer Breeze and the Mini Cup). Now I have a good idea of what I need and how it’s all going to fit together.
Workspace
Boat building needs to be done in an area protected from the weather. The only clear choice for me was our garage. Our Garage was built in 1929 probably for a Model T Ford. Good thing my boat is only 12
Tools
Saws (table, hand and jig)
Measuring tape, carpenter and bevel square
Drill and screwdrivers
Materials
1. Three 4X8 sheets of ¼ inch ply wood (plans for marine grade BUT some have suggested shop grade is as good and perhaps better than exterior grade).
2. ¾ in stock hemlock or straight grain fir for gunwales, chines, transom and seats.
3. Two 2x4s in 15 foot lengths for the mask and boom
4. Glues (epoxy for below water line, premium grade adhesive and water resistant carpenters glue for other areas)
5. About 1000 screws (stainless steel or brass) in various lengths
6. Polytarp and duct tape for the sail
7. Close line type rope for the rigging
8. About 12 eye bolts
9. Auto body filler putty. fiberglass and high gloss latex or oil enamel paint
Tuesday, September 30, 2008
Posting # 1 Decisions ….
I am not qualified to build a boat. I don't think any of my previous woodworking projects and experiences prepares me for the complexity of boat building. When it comes to building I tend to be impulsive and any projects taking more than two days are usually left undone. Obviously if this boat is going to be built I need to do things differently.My wish list:
1. Car top transporting
2. Hold a crew of two or less (Max load weight = 500 pounds)
3. Converts to a rowboat when the wind is not cooperating
4. Made of stock material I can get from my local Home Depot
5. Easy to build
6. Looks beautiful
7. Have a “retractable or removal keel”
First I have to decide the options for a “retractable or removal keel”.
The keel converts the forward motion into a windward lift, countering the leeward push of the sail this causes the boat to go forward instead of moving side ways or tipping over. The keel is retracted or removed when beaching, going downwind or when rowing. A small sailboat that converts to a rowboat needs to have “a retractable or removal keel”. There are three options for this type of keel.
1. Leeboards are entirely outside the boat with all the mechanism readily accessible, which is good. BUT they are generally ugly.2. Centerboards can easily be raised partially, either in shallow water or to change the helm balance. They are more trouble to build, the trunk is a lot larger and occupies a very useful part of the boat, the pivot requires careful planning or it can leak.
3. Daggerboards take up a lot less space in the boat when they’re down. They are a problem in shallow water because they’re hard to raise. Sailing right up on the beach requires good timing and coordination. They can be damaged by running into something hard at speed.
Decision Made:
After doing hours of online research online I have decided on using parts of two plans – risky?
1. The Summer Breeze

is a fairly simple boat to build but looks more like a plain Jane rowboat and the Lee board is unsightly
2. The Mini Cup

is harder to build, smaller looks great but designed for warmer waters (expect to get wet in this boat).
My Plan
I will build the Summer Breeze’s hull with out the Leeboard and will use the plans for the Mini Cup’s Daggerboard instead. I will add a deck top similar to the Mini Cup’s. I also like the design for the sail and rigging for the Mini Cup and will use that design for my boat.
Subscribe to:
Posts (Atom)